Hardware
|
|
|
| Ball Joint, Plastic, Snap On | Ball Joint, Quick Connect | Barrel, Locking, Rod, Brass, 3/8" |
Plastic snap on 90° ball joints for cross shaft to pull rod link connection on Sho~Bud Mavericks and both ends of drag link rods on Sho~Bud D10's. Male/Female thread configuration with #10-32 threads. Ball studs have been machined so as not... | Quick Connect 90° and 180° ball joints. | Brass Rod Locking Barrel Ø1/4" x 5/16" & 3/8" Long |
$8.18 (1) | $7.50 (3) | $9.00 |
|
|
|
|
| Barrel, Locking, Rod, Brass, 5/16" | Block, Triple Raise/Lower, | Bracket, Free Stand, Knee Lever, MSA |
Brass Rod Locking Barrel Ø1/4" x 5/16" & 3/8" Long | Tom Bradshaw designed device for double raise/lower changers | Bracket that will allow you to mount 2 knee levers inboard of the rear rail. This bracket may also be positioned anywhere you have room. Fits most all pre-1985 MSA pedal steel guitars. |
$9.00 | $10.25 | $25.81 |
|
|
|
| Bracket, Free Stand, Reversing, MSA | Clip, E-Ring, 7/64" | Clip, Hair Pin, .042 |
Bracket that will allow you to mount a right hand knee lever with a reversing link, inboard of the rear rail. | E-Clip used primarily on Emmons Guitars to retain pull rod in the bell crank. | Hair Pin Clip used on some pedal steel guitars to retain the pull rod on the bellcrank. |
$28.75 (1) | $4.00 | $4.00 (1) |
|
|
|
| Clip, Snap Ring, 1/4" | Clip, Snap Ring, 5/16" | Clip, Spring, Retaining, Pull Rod |
Snap Ring used primarily on Sho-Bud Pro I & II to retain round brass rod pull on 2 hole puller. | Snap Ring used primarily on Sho-Bud Pro Series Cross Shafts |
|
$4.00 | $4.50 | $8.00 |
|
|
|
| Nut, Acorn, #10-32 | Rod, Pedal, Ø4.2mm | Screw, Pan Head, Slotted, #6-32 x 3/8" |
Acorn Nut for covering the thread on the shoulder bolt which attaches the RKR to the rear rail on MSA pedal steel guitars. Also used on the pivot screws that attach the knee lever to the shaft bracket. | Pedal Rods in a variety of lengths. | Pan Head Slotted Screw used primarily on the Pre-1985 MSA's to secure the sheet metal tab of the pedal pull. |
$0.49 | $12.50 | $0.16 |
|
| |
| Screw, Shoulder, Socket Head | Screw, Socket Set, #10-32 x 3/16" | Shaft, Pedal, MSA |
Shoulder Screw used primarily on the Pre-1985 MSA's. | Socket Head Set Screw used primarily on the Pre-1985 MSA's to secure the Pedal Axel in the pedal. These are Alloy Steel #10-32 x 3/16" long. Price is for 1 package of 10 screws. | Pedal Support Shaft for Pre-'85 MSA pedal steel guitars. |
$6.00 | $2.50 | $2.00 |
|
| |
| Washer, Fiber, Ø.125 ID, Ø.250 OD | Washer, Nylon, Ø.505 ID, Ø.750 OD, .032 Thick | |
| Nylon washer for MSA Changers. These washers are used between the finger assemblies. Actual thickness varies between .032-.036". Packages of 11 or 13 washers. | |
$5.00 | $5.50 | |
